Demontage von Sturmey-Archer Naben

Aus WikiPedalia
Die druckbare Version wird nicht mehr unterstützt und kann Darstellungsfehler aufweisen. Bitte aktualisiere deine Browser-Lesezeichen und verwende stattdessen die Standard-Druckfunktion des Browsers.

Dieser Artikel beinhaltet einen allgemeingültige Demontageanleitung für klassische Sturmey-Archer Naben. Spezialitäten einzelner Modelle findet man hier nicht. Dazu sollte man im Artikel Wartung klassischer Sturmey-Archer Naben nachsehen, ob es tiefer gehende Informationen zu einzelnen Modellen gibt.

Unscrew everything from the left-hand end of the axle

When gear and brake controls and electrical wires (if any) have been disconnected and the wheel removed from the cycle frame , dismantling of the hub begins with the removal of the left-hand locknut, the washers (if any) and the left-hand cone. A note should always be made of their order and number so that they may be put back correctly when the hub is re-assembled. In particular, different numbers of spacer washers may be fitted, depending on the spacing and chainline. Left Axle Nut Left Axle Nut HMN128 HMN128 Axle Washer Axle Washer HMW155 or HMW494 Locknut Locknut hmn132 HMN132 Spacer Spacer HMW129 HMW129 Cone Cone HSA101 HSA101 The parts shown above are common to most models that do not incorporate a brake.

Models With Built-in Brake

Where a brake is incorporated in the hub, the brake unit must be removed before the left-hand cone can be unscrewed. The last washer to be taken off before coming to the brake plate is the notched adjusting washer which fits over the flats on the end of the cone for normal wheel adjustment purposes. When this notched washer has been taken off, lift out the brake arm and shoes as a complete unit, and then proceeds to unscrew the left-hand cone.

Models With Dynohub Generator

Similarly, the generator must first be removed from hubs incorporating a Dynohub lighting unit. The procedure is explained in detail in the appropriate chapters of this section of the catalogue


Unscrew the right-hand ball ring and internal assembly

Next, use a hammer and punch to unscrew the right-hand ball ring

As you withdraw the internal assembly, try to avoid touching the low-gear pawls while the unit is held sprocket-side up, because there is a risk of the pawl pins falling out if you relieve the spring tension that holds them in place.

The right hand ball ring has a two-start thread and must be replaced in its original position, that position must be marked. String or adhesive tape may be attached to the spoke nearest to the letters ' SA' which are stamped in one of the notches on the ring. The whole internal can now be withdrawn from the hub shell. (This is rarely a problem in practice.)

This is a standard right-hand thread, turn it counterclockwise to remove it.

Removal of the right-hand ball ring in the case of the TCW is described the chapter headed To Dismantle the TCW Hub.

In all other cases, the right-hand ball ring, which has a right-hand thread, is loosened by means of a 'C' spanner or a hammer and square-ended punch against one of the notches. If it is required to remove the sprocket, insert a thin screwdriver in the groove of the driver which comes nearest to the opening in the circlip and prise off the circlip. The spacing washers, sprocket and outer dust cap may then be lifted off the driver. There must always be two 1/16" washers. Careful note should be made of their position and also whether the sprocket offset is facing inwards or outwards, as they must all be put back in the same way in order to maintain the original chain line.

Quelle

Dieser Artikel basiert auf dem Artikel Home Made "Drop Bolts" von der Website Sheldon Browns. Originalautor des Artikels ist Sheldon Brown.