Entfaltung

Aus WikiPedalia

Unter der Entfaltung oder Ablauflänge versteht man die Länge der Strecke, die ein Fahrrad durch eine Umdrehung der Tretkurbeln zurückgelegt.

Zur Berechnung der Entfaltung muss man den Abrollumfang des Rads und die Übersetzung von Kettenblatt und Ritzel kennen.

Der Abrollumfang eines Rads mit 28 Zoll ist grob gerechnet rund 2,16m Die Übersetzung von einem Kettenblatt mit 44 Zähnen und einem Ritzel mit 19 Zähnen ist rund 0,432 Die Entfaltung beträgt dann 2,16m/0,432 = 5m Bei einer Umdrehung der Tretkurbeln pro Sekunde ergibt sich so eine Fahrgeschwindigkeit von 5 m/s = 18 km/h

Gain Ratio - Die Sheldon Brown Methode zur Berechnung der effektiven Entfaltung

Bestimmung von Fahrrad-Übersetzungen

Fahrradfahrer finden es häufig nützlicjh, eine numerische Angabe zu den Übersetzungen Ihrer Fahrräder zur Hand zu haben. Diese Angaben erlauben es Ihnen, aussagekräftige Kriterien zur persönlichen Anpassung Ihrer Übersetzungen an der Hand zu haben und erlauben es zudem die Leistungsfähigkeit einzelner Fahrräder untereinander vergleichbar zu machen.

Dazu gibt es mehrere Systeme, keines erscheint vollständig zufriedenstellend zu sein. An dieser Stelle soll ein Vorschlag für ein neues, akkurateres und universelleres System vorgestellt werden.

Existierende Systeme

Vorne/Hinten

Fahrradfahrer, die nur mit einem sehr eng begrenzten Umfeld der Fahrradwelt in Berührung kommen, reichen meist die Kettenblatt- und Ritzelgröße, die sie in Benutzung haben. Es erscheint lästig und verwirrend zwei Zahlen benutzen zu müssen, wenn man doch nur eine Zahl benötigt. So ist zum Beispiel 39/14 das Gleiche wie 53/19, auch wenn es nicht auf den ersten Blick so scheint. Da bei Rennrädern sind für gewöhnlich nur 4 Kettenblattgrößen in Gebrauch (39,42, 52 und 53) sind, ist dies noch überschaubar für Fahrradfahrer, die nur mit dieser Art Maschinen in Berührung kommen.
Breiter aufgestellte Radler, die vermutlich mit einem breiteren Spektrum an Kettenblättern und Reifengrößen zu schaffen haben, benötigen ein weiterentwickeltes System, um zu ersehen, dass 46/16 am Mountainbike, 42/12 am Moulton und 52/14 an Ihrem "Bike Friday" das gleiche wie die schon erwähnten 39/14 und 53/19 am Strassenrenner sind.
Dieses System wird aber nutzlos, sobald Planetengetriebe ins Spiel kommen.

Übersetzungs Zollmaß

The simplest system in common use is the "gear inch" system. This dates back to before the invention of the chain-drive bicycle. It originally was the diameter of the drive wheel of a high-wheel bicycle. When chain-drive "safety" bikes came in, the same system was used, multiplying the drive wheel diameter by the sprocket ratio. It is very easy to calculate: the diameter of the drive wheel, times the size of the front sprocket divided by the size of the rear sprocket. This gives a convenient two- or three-digit number. The examples listed above are all around 74-75 inches. The lowest gear on most mountain bikes is around 22-26 inches. The highest gear on road racing bikes is usually around 108-110 inches. Unfortunately, the handwriting is on the wall for all inch-based measurement systems.

Entfaltung in Metern

In countries that use metric measurements, the usual system is "development" in meters. This is the distance that the bicycle moves with each revolution of the pedals. This system is a bit more cumbersome than the gear inch system, for two reasons. First, it is a little more difficult to calculate: wheel diameter in meters x front sprocket / rear sprocket x pi. Having to multiply by a constant (an irrational one, no less!) needlessly complicates things. Also, the resulting value is a less convenient number to work with, a single digit plus two decimals. For example a road bike's 52/13 would be exressed: 8.64. A mountain bike's 24/28 would be: 1.78.

Wie verhält es sich mit Kurbellängen?

All of these systems share a common inadequacy: none of them takes crank length into account! The fact is that a mountain bike with a 46/16 has the same gear as a road bike with a 53/19 only if they have the same length cranks. If the mountain bike has 175's and the road bike 170's, the gear on the mountain bike is really about 3% lower!

Vorschlag für einen neuen Standard

I would like to propose a new system, which does take crank length into account. This system is independent of units, being expressed as a pure ratio.

This ratio would be calculated as follows: divide the wheel radius by the crank length; this will yield a single radius ratio applicable to all of the gears of a given bike. The individual gear ratios are calculated as with gear inches, using this radius ratio instead of the wheel size.


You can calculate gain ratios, gear inches or meters development with my Online Gear Calculator or with your slide rule Spoke Divider

An Example:

   A road bike with 170 mm cranks: (The usual generic diameter value for road wheels is 680 mm, so the radius would be 340 mm.)
   340 mm / 170 mm = 2.0. (The radius ratio)
   2.0 X 53 / 19 = 5.58
   This number is a pure ratio, the units cancel out. I call this a "gain ratio" (with thanks to Osman Isvan for suggesting this term.) What it means is that for every inch, or kilometer, or furlong the pedal travels in its orbit around the bottom bracket, the bicycle will travel 5.58 inches, or kilometers, or furlongs.

Another example:

   A mountain bike with 26 inch wheels (13 inch radius) and 6 3/4" cranks:
   13" / 6 3/4" = 1.93
   1.93 X 46 / 16 = 5.54
   Remember, the "radius ratio" only has to be figured out once for a given bike, because it is the same in all gears. Any individual gear is calculated as:
   Radius ratio X front(teeth) / rear(teeth)
   Any measurement units may be used, as long as the same units are used for both the wheel diameter and crank length.


You can calculate gain ratios, gear inches or meters development with my Online Gear Chart or with your slide rule Spoke Divider

Radius Ratios for Common Crank Sizes:

Tire Size Tire Radius 165 mm 170 mm 172.5 mm 175 mm 180 mm
I.S.O. 630:
27 X 1 3/8 345 2.091 2.029 2.000 1.971 1.917
27 X 1 1/4 343 2.079 2.018 1.988 1.960 1.906
27 X 1 1/8 342 2.073 2.012 1.983 1.954 1.900
27 X 1 340 2.061 2.000 1.971 1.943 1.889
I.S.O. 622:
700 X 56 370 2.242 2.176 2.145 2.114 2.056
700 X 50 365 2.212 2.147 2.116 2.086 2.023
700 X 44 354 2.145 2.082 2.052 2.023 1.967
700 X 38 347 2.103 2.041 2.012 1.983 1.927
700 X 35 345 2.091 2.029 2.00 1.971 1.917
700 X 32 342 2.073 2.012 1.983 1.954 1.900
700 X 28 336 2.036 1.976 1.948 1.920 1.867
700 X 25 335 2.030 1.971 1.942 1.914 1.861
700 X 20 332 2.012 1.953 1.925 1.897 1.844
I.S.O. 559:
26 X 2.125 330 2.000 1.941 1.913 1.886 1.833
26 X 1.9 324 1.964 1.906 1.878 1.851 1.800
26 X 1.5 312 1.891 1.835 1.809 1.783 1.733
26 X 1.25 311 1.884 1.829 1.803 1.778 1.728
26 X 1.0 (559 mm) 305 1.848 1.794 1.768 1.743 1.694
I.S.O. 571:
26 x 1 (650C) 311 1.884 1.829 1.803 1.778 1.728
Other:
Wide Tubular 338 2.048 1.988 1.959 1.931 1.878
Narrow Tubular 335 2.030 1.971 1.942 1.914 1.861
26 X 1 3/8 (590 mm) 330 2.000 1.941 1.913 1.886 1.933
24" 305 1.848 1.794 1.768 1.743 1.694
24 x 1 (520) 279 1.691 1.641 1.617 1.594 1.550
20 X 1.75 (406 mm) 254 1.539 1.494 1.472 1.451 1.411
20 X 1 1/4 (451 mm) 257 1.558 1.512 1.490 1.469 1.428
17 x 1 1/4 (369 mm) 211 1.279 1.241 1.223 1.206 1.172
16 x 1 3/8 (349 mm) 204 1.236 1.200 1.183 1.166 1.133


Quellen