Wartung von Sturmey-Archer Acht-Gang-Naben

Aus WikiPedalia

Die Acht-Gang Sturmey-Archer Naben haben ein innovatives Design mit drei hintereinanderliegenden Planetensystemen. Wenn ein Sonnenrad eines Moduls mit der Achse verbunden ist, erhöht sich die Übersetzung, wenn nicht, ist die jeweilige Übersetzung 1:1. Jedes der drei Module entwickelt eine unterschiedliche Übersetzung. Die acht möglichen Kombinationen ergeben die acht Gänge der Nabe. Da diese Naben nur Übersetzungssprünge nach oben darstellen können, benötigen Sie ein wesentlich kleineres Kettenblatt als üblich. Das macht sie für Fahrräder mit kleinen Laufrädern interessant. Diese Naben sind im kleinsten Gang besonders effizient, in dem die Kraftübertragung direkt vom Mitnehmer auf den Nabenkörper erfolgt. Im höchsten Gang sind sie dahingegen am wenigsten effizient, da dort alle drei Module benutzt werden.

Schnittmodell einer Sturmey-Archer X-RD8(W) Acht-Gang-Nabe mit Trommelbremse
Schnittmodell einer Sturmey-Archer X-RD8(W) Acht-Gang-Nabe mit Trommelbremse

Die Modellbezeichnungen beinhalten den Buchstaben "F" für Freilauf, "K" für Scheibenbremse und "D" für Trommelbremse. Die nicht mehr erhältliche X-RR8 hatte eine AUfnahme für eine Shimano Rollenbremse. Es gibt kein Modell mit Rücktrittbremse.


Die Übersetungsabstufungen für die Serie mit breiten Übersetzungsabstufungen wurde 2009 eingeführt. Für das Model X-RF8 (W) usw. sehen sie wie folgt aus:

Übersetzung 1.000 1.303 1.481 1.677 1.931 2.186 2.485 3.239
Sprung 30% 14% 13% 15% 13% 14% 30%

Die Übersetzungssprünge der ersten Acht-Gang Naben Serie z.B. der X-RF8 usw, sahen wie folgt aus

Übersetzung 1.000 1.281 1.450 1.644 1.858 2.106 2.384 3.054
Sprung 28% 13% 13% 13% 13% 13% 28%


Die Zahlen basieren auf Zählung der Zanhräderzähne.

Siehe auch

Bei einem einfachen Planetengetriebe ist es schwierig eine nicht 1:1 Übersetzung darźustellen, die nahe an der 1:1 Übersetzung liegt. Daher ist der erste Sprung bei diesen Naben immer recht groß. Um zu große Sprünge in der Mitte zu vermeiden, wird ein großer Übersetzungssprung am oberen Ende des Bereichs angesetzt. Daher ist es sinnvoll, den zweithöchsten Gang als Reisegang für flache Strecken zu wählen. Damit hat man einen Übersetzungsdurchmesser von rund 75 Zoll (6,0 Meter Entfaltung bzw. ein Vortriebsverhältnis von 5,5). Jeder kleinere Gang als Reisegang würde den höchsten Gang zu hoch einstufen, damit er noch sinnvoll ist. Auf der anderen Seite benötigt man im Flachland nicht wirklich kleine Gänge. Daher könnte man - wenn man dort lebt - insgesamt die Übersetzunge höhger ansetzen, um in dieser Gegend mehr Gänge zur Verfügung zu haben.

Jeder Mensch braucht einen anderen (Pedal)takt.

Siehe auch

Werbung:

Technik

A few technical issues are important when specifying, installing or rebuilding these hubs:

  • The right-side ball ring unscrews counterclockwise from the hub shell, according to the most reliable . information we have. Sturmey-Archer has published information indicating both directions! This ball ring does not include a ratchet, unlike those of most Sturmey-Archer internal-gear hubs.
  • Reliability has been an issue with these hubs, though it appears to be improving with newer production.
  • These hubs are grease-lubricated and have no port through which oil can be introduced. Oil can be added after unscrewing the left ball cup. These hubs should be disassembled and relubricated periodically. Disassembly is fairly easy with the newer models. It may be advisable to relubricate before installing a new hub: see advice here.
  • Stout antirotation washers should be used, preferably both inside and outside the dropouts. See advice here. Also, gear down and spin rather than pushing hard in a high gear. As the lowest gear ratio is unity, torque on the axle decreases, the lower the gear.
  • The sprocket is unlike the one used on most other internal-gear hubs. The center hole is much larger, and the sprocket is available only with 20, 23 or 25 teeth. The sprocket has three lugs and is held in place by a circlip (snap ring). The 20 and 23-tooth versions are flat; the 25-tooth version is also available dished.
  • The brakeless version is especially well-suited to older bicycles with narrow rear dropout spacing. By the choice of locknuts and by using the brakeless version of the hub, the overlocknut distance can be smaller than for any other internal-gear hub with 7 or more speeds -- as little as 115 mm.
  • If you're going to use rim brakes and a 130mm or 135mm overlocknut distance, get the "K", disc brake version rather than the "F" freewheel version. The "K" has a natively wider hub shell and better bearing placement. (Thanks to Prester John on the Geared Hub Bikes e-mail list for this advice.) But this version may also require a larger chainline.
  • Sturmey-Archer sells cranksets adapted to this hub, with tooth counts in the 30s, and designed to work with a full chain case.
  • These hubs shift with a pulley mechanism concentric with the axle inboard of the frame, and use different shifters from other Sturmey-Archer hubs. The newer (W) versions cleverly allow the pulley mechanism to be installed at different angles, so that only one type or antirotation washers is necessary, regardless of the angle of the dropout slots.

Technische Informationen zu Modellen ab 2009

The 2009- models are very similar to the first series, but a different tool is used to remove the screw-in right ball cup, and obviously, many of the internal parts are different. A part number ending in (W) is sometimes used to distinguish the 2009- hubs from the earlier models, but not consistently, possibly leading to confusion. The ball ring of the newer-series hubs has six notches for the ball-ring removal tool, the older series, two notches. Parts in parts lists for hubs made since 2009, with or without the (W), are compatible. You may compare the two parts lists for the XRD8(W) linked below to confirm this. Fittings for these hubs Installation instructions for these hubs Model Features Documentation S80 (W) No brake, steel shell Parts list (for X-FR8 (W)) Video of operation X-RD8(W) Drum brake Parts list Older parts list with installation instructions but missing a few options X-RF8 (W) No brake Parts list Video of operation X-RK8 (W) Disk brake fitting Parts list Installation instructions.

Technische Informationen zu Modellen ca. 2004 bis 2009 (eingestellt)

Technical documentation is available for some of these models. Model Features Documentation X-RD8 Drum brake

Technical information Disassembly instructions from an owner. X-RF8 No brake Technical information Another source Installation X-RK8 Disk brake fitting Like X-RF8 X-RR8 Roller brake Like X-RF8

Siehe auch

Another article on this site covers topics common to many Sturmey-Archer hubs. Please read that article to learn about

  • Date and model identification
  • Cable replacement
  • Cable adjustment
  • Cone Adjustment
  • Anti-rotation washers
  • Axle length
  • Lubrication

There are also articles on this site more generally about

  • Internal-gear hubs
  • Cribsheet -- Sturmey-Archer hubs since the 1930s
  • Disassembly of Sturmey-Archer hubs
  • Special alignment and adjustment (Dynohubs, hub brakes, shifter parts)
  • Use and maintenance of Sturmey-Archer hubs
  • Parts and names (older Sturmey-Archer hubs)
  • Sturmey-Archer corporate history and hub models


Sturmey-Archer Informationen

  • Official Site
  • old Sturmey-Archer logo Heritage site
  • Three-Speed Parts from Harris Cyclery
  • English Three Speeds, Care and Feeding
  • Internal-Gear Hubs
  • Sturmey-Archer Hubs, General Information
  • Sturmey-Archer 1902-1952
  • Sturmey-Archer 1935-38 Catalogues
  • Evolution of the Raleigh Sports
  • Sheldon's 8-speed Raleigh Twenty
  • John Allen's spreadsheets of internal-hub gear ratios
  • Martin Hanczyc's roadster pages.
  • Tony Hadland's Sturmey-Archer Pages including the 1956 master catalogue with rebuilding information for SWs and others.
  • Hubstripping web site
  • Retro Raleighs
  • SW Hubs by Brian Hayes
  • Jane Thomas's site with Sturmey-Archer service manuals.
  • Menotomy Vintage Bicycles
  • Chat forum on English bikes.

Quelle

Dieser Artikel basiert auf dem Artikel Servicing Sturmey-Archer 8-Speed Hubs von der Website Sheldon Browns. Originalautor des Artikels ist John Allen.