Bürokraten, editor, Administratoren
15.322
Bearbeitungen
Montage und Justage von Zangenbremsen: Unterschied zwischen den Versionen
Aus WikiPedalia
Montage und Justage von Zangenbremsen (Quelltext anzeigen)
Version vom 5. Juli 2018, 08:15 Uhr
, 5. Juli 2018→Versenkte Bremsenbefestigung: Ergänzungen...
K (→Versenkte Bremsenbefestigung: ...) |
(→Versenkte Bremsenbefestigung: Ergänzungen...) |
||
| Zeile 94: | Zeile 94: | ||
{{Ergänzung|Ergänzung|Sheldons Artikel ist von 1997. Hier merkt man wieder, das die Zeit nicht stehen bleibt.}} | {{Ergänzung|Ergänzung|Sheldons Artikel ist von 1997. Hier merkt man wieder, das die Zeit nicht stehen bleibt. Inzwischen sind klassische Bremsenbefestigungen sehr rar geworden und man findet am Markt überwiegend Bremsen mit versenkten Befestigungen.}} | ||
====Montage von versenkten Bremsenbefestigung an älteren Rahmen==== | ====Montage von versenkten Bremsenbefestigung an älteren Rahmen==== | ||
; | ;Hinten - hier hat man drei Möglichkeiten: | ||
[[Datei:Brakefrontcropped300.JPG|right|Vor den Sitzstreben montiert]] | [[Datei:Brakefrontcropped300.JPG|right|Vor den Sitzstreben montiert]] | ||
*You might mount a rear brake for recessed mounting ahead of the seatstays, as long as the back side of the brake bridge can be safely drilled out. This is more likely to work with a single-pivot or dual-pivot brake, due to the difficulty of routing the cable with a centerpull. Use an 8 mm or USA letter-size O drill bit. A 5/16"drill bit is slightly smaller, and you may have to ream the hole slightly. Radiused washers (as shown on the nutted-style brake in the photo above) must be used if the brake bridge has no flat mounting surfaces. The washer that goes under the nut must be drilled out, and so must the brace of a baggage rack, if it attaches to the brake bolt. Remember to reverse the brake shoes if they are single-ended. | *You might mount a rear brake for recessed mounting ahead of the seatstays, as long as the back side of the brake bridge can be safely drilled out. This is more likely to work with a single-pivot or dual-pivot brake, due to the difficulty of routing the cable with a centerpull. Use an 8 mm or USA letter-size O drill bit. A 5/16"drill bit is slightly smaller, and you may have to ream the hole slightly. Radiused washers (as shown on the nutted-style brake in the photo above) must be used if the brake bridge has no flat mounting surfaces. The washer that goes under the nut must be drilled out, and so must the brace of a baggage rack, if it attaches to the brake bolt. Remember to reverse the brake shoes if they are single-ended. | ||
| Zeile 103: | Zeile 103: | ||
* Front brakes for recessed mounting have bolts that are long enough to use them as rear brakes, if you substitute the appropriate washers and a 6 mm nut. | * Front brakes for recessed mounting have bolts that are long enough to use them as rear brakes, if you substitute the appropriate washers and a 6 mm nut. | ||
; | ;Vorne - auch hier hat man drei Möglichkeiten: | ||
* Drill out the back of the fork crown, just as is described above for the rear brake. | * Drill out the back of the fork crown, just as is described above for the rear brake. | ||
