Die Sturmey-Archer ASC Fixed Gear Drei-Gang-Nabe/Wartung der Sturmey-Archer ASC Fixed Gear Drei-Gang-Nabe: Unterschied zwischen den Versionen
Aus WikiPedalia
(Tabeelle geradegerückt) |
(typos) |
||
Zeile 1: | Zeile 1: | ||
[[SunRace]]/Sturmey-Archer hatte zwischenzeitlich eine neuere Fixed-Gear Drei-Gang-Nabe - die [[S3X]] - auf den Markt gebracht. Wenn man sich die Fortschritte von Sunrace mit Sturmey- | [[SunRace]]/Sturmey-Archer hatte zwischenzeitlich eine neuere Fixed-Gear Drei-Gang-Nabe - die [[S3X]] - auf den Markt gebracht. Wenn man sich die Fortschritte von Sunrace mit Sturmey-Archer Produkten ansieht, kann man erwarten, dass die neuere Nabe zuverlässiger funktioniert als das Original. | ||
Auf dieser Seite kümmern wir uns allerdings um die Wartung der früheren Sturmey-Archer Fixed-Fear-Nabe. | Auf dieser Seite kümmern wir uns allerdings um die Wartung der früheren Sturmey-Archer Fixed-Fear-Nabe. |
Version vom 17. April 2020, 11:14 Uhr
SunRace/Sturmey-Archer hatte zwischenzeitlich eine neuere Fixed-Gear Drei-Gang-Nabe - die S3X - auf den Markt gebracht. Wenn man sich die Fortschritte von Sunrace mit Sturmey-Archer Produkten ansieht, kann man erwarten, dass die neuere Nabe zuverlässiger funktioniert als das Original.
Auf dieser Seite kümmern wir uns allerdings um die Wartung der früheren Sturmey-Archer Fixed-Fear-Nabe.
CODE Nr. | Beschreibung | CODE Nr. | Beschreibung |
---|---|---|---|
K831 | Axle, 5 1/2" long | K228 | R H. Ball Ring |
K805A | Low Gear Dog | K230Z | Ball Cage with 3/16" balls |
K806 | Dog Sleeve | K462 | Driver, 3-Lug |
K402 | Low Gear Key | K657 | Driver, 12-Spline |
K809A | Secondary Sun Pinion | K67Z | Ball Cage with 8 1/4" balls |
K811 | Locating Plate | LB405 | Outer Dust Cap |
K 412 | Locking Washer | K506Z | Axle Cone with Dust Cap |
K812 | Locknut | K516 | R.H. Cone Locking Washer |
K8l5A | Secondary Planet Cage | K718Z | Shell, 40 holes, with Ball Cup |
K816A | Secondary Planet Pinion | K7l8AZ | Shell, 36 holes, with Ball Cup |
K8l0B | Low Gear Spring | K227 | Connection Locknut |
K808 | Primary Sun Pinion | X42A | Axle Spacing Washer |
K715 | Planet Cage | K47A | Cone Locknut |
K16 | Planet Pinion | K521 | Axle Locking Washer |
N24 | Pinion Pin | N190 | L.H. Axle Nut |
K716 | Indicator | N200 | R.H. Axle Nut |
X8 | Collar for Compensator Spring | K229 | Sprocket Dust Cap |
K8l3B | Compensator Spring | K464 | Sprocket, 14 teeth, 3-Lug |
K527 | Clutch Sleeve | K465 | Sprocket, 15 teeth, 3-Lug |
K505A | Sliding Clutch | K466 | Sprocket, 16 teeth, 3-Lug |
K526A | Axle Key | K467 | Sprocket, 17 teeth, 3-Lug |
K807ZA | Coupling complete | K468 | Sprocket, 18 teeth, 3-Lug |
K807Z | Coupling complete, quick-release type. Not illustrated | K469 | Sprocket, 19 teeth, 3-Lug |
K74OAZ | Quick Release Connection. Not illustrated | K470 | Sprocket, 20 teeth, 3-Lug |
K528A | Thrust Ring | X49 | Sprocket Spacing Washer |
K411 | Thrust Washer | K463 | Circlip |
K530B | Clutch Spring | K214 | Sprocket, 14 teeth, 12-Spline |
K529 | Spring Cap | K215 | Sprocket, 15 teeth, 12-Spline |
K511B | Gear Ring | K216 | Sprocket, 16 teeth, 12-Spline |
K217 | Sprocket, 17 teeth, 12-Spline | ||
K218 | Sprocket, 18 teeth, 12-Spline | ||
K219 | Sprocket, 19 teeth, 12-Spline | ||
K220 | Sprocket, 20 teeth, 12-Spline | ||
K36 | Sprocket Lock Ring |
Zusammenbau einer ASC Nabe
Proceed as follows:
- Prepare the following preliminary sub-assemblies:
- Fit the ball cage into the left-hand ball cup, with the ring of the ball-retainer facing outwards and the recess in the dust cap also facing outwards. If a new ball-retainer is being fitted, the dust cap also should be new.
- Fit the ball cage into the driver, with the ring of the ball- retainer facing outwards and the recess in the dust cap also facing outwards. If a new ball-retainer is being fitted the dust cap also should be new. If the sprocket has been removed see No. 27 below.
- Smear grease in the channels of the dust cap of the left-hand ball cup and the driver and in the recess of the right-hand ball ring. Do not use grease anywhere else.
- Hold the axle in a vise, with the smaller slot uppermost, and fit the low-gear clutch sleeve with its flange on top.
- Slip the small low-gear key through the holes of the low-gear clutch sleeve, making sure that the hole through the key is in line with the bore of the axle. Hold the key temporarily in position by dropping the indicator rod down the axle through the key.
- Holding the indicator rod in position with one finger, remove the axle from the vise and hold it the other way up. Fit the low-gear clutch on to the axle, with the four dogs pointing downwards.
- Fit the large low-gear spring and the primary sun pinion, with its four large legs pointing downwards and so engaging the low-gear clutch. (The low-gear spring, the compensating spring, and the clutch spring must be of the same series. If one has to be replaced, the other two must be.)
- Slip the indicator rod out of the axle (the low-gear clutch key will now stay in position) and put the axle back in the vise.
- Fit the primary planet cage complete.
- Drop the compensating spring down the axle, collar first.
- Fit the clutch sleeve (flange first) and the sliding clutch with the recess over the flange of the sleeve.
- Lift the clutch sleeve and the clutch up to the top of the long axle slot and insert axle key through the clutch sleeve, making sure That the two flats on The key are facing upwards.
- Fit the indicator coupling by passing the rod down the axle through the axle key and onto the compensator spring. Note that the indicator coupling must always be fitted before the indicator rod.
- Remove the axle from the vise and push the indicator rod into the left-hand end of the axle. Press the assembled mechanism down on a flat surface to force the indicator rod into the axle, at the same time pressing down on the sliding clutch. Then rotate the indicator chain to screw it to the indicator rod. When the chain is felt to be fully screwed home insert a small screwdriver into the slot of the indicator rod and exert a slight extra pressure on the chain, to make sure that the indicator and the rod are both fully screwed together, taking care not to twist off the small threaded end.
- Fix the axle in thc vise again and make sure that the clutch slides quite freely on the axle when the indicator chain is moved up and down.
- Fit the thrust collar, making sure that both slots fit over the flats of the axle key. Add the thrust washer.
- Fit the gear ring, the ball ring (with ball cage), the driver, the axle spring and the clutch spring cap in that order.
- Fit the right-hand cone and screw it up finger tight. Then slacken it back half a turn and lock it in that position with the special washer and locknut. On no account must the cone be unscrewed more than half a turn, as that would throw the gear mechanism out of adjustment.
- Remove the assembled mechanism from the vise and replace it the other way up.
- Fit the secondary planet cage, with the pins upwards and the slots engaging the limbs of the low-gear dog.
- Fit the secondary planet pinion.
- Fit the secondary sun pinion, with the recess downwards so that the sun pinion engages with the square flats on the axle.
- Fit the locating plate and tab washer and tighten the locknut. Turn over the edge of the washer on two opposite sides of the locknut.
- Remove the assembled mechanism from the vise, hold it vertically with the planet cage uppermost and pour about two teaspoonfuls of a good quality thin oil into the cage.
- Insert the assembled mechanism into the hub shell and screw up the right-hand ball ring finger-tight only.
- Make sure that the marks put on the ball ring and the hub flange before dismantling will register properly, and then screw up tightly.
- Fit the left-hand cone, washer and locknut in the arrangement noted when dismantling, and adjust the hub as described in The Fitting and Adjustment of Sturmey-Archer Hubs.
- Fit any special washers noted when dismantling the hub.
- If the sprocket has been removed from the driver, fit the outer dust cap over the driver before replacing the sprocket, and see that the dust cap is properly centered on the flange of the driver. Replace the sprocket and the spacing washers in the arrangement noted when dismantling, and add the circlip.
- Replace the wheel in the cycle frame and adjust the gear as described in The Fitting and Adjustment of Sturmey-Archer Hubs.
Quelle
Dieser Artikel basiert auf dem Artikel Servicing The Sturmey-Archer ASC Three-Speed Fixed-Gear Hub von der Website Sheldon Browns. Originalautor des Artikels ist Sheldon Brown.
Weitere interessante Artikel zum Thema Sturmey-Archer
Weitere interessante Artikel zum Thema Nabenschaltung
Weitere interessante Artikel zum Thema Sheldon Brown
- Knarzen, Knacken und Quietschen
- Sattelstützenmaße
- Ritzelabstände (Tabelle)
- Auswechselbarkeit von Vierkant-Kurbelaufnahmesystemen bei Innenlagern
- Kettenlinienstandards (Tabelle)
- Ein bequemer Sattel
- Nabenbreiten (Tabelle)
- Alles über Nabenschaltungen
- Shimano Nexus und Alfine Acht-Gang-Naben
- Reifengrößen
Weitere interessante Artikel zum Thema Workshop