Das 1x1 der Trommelbremsen

Dieser Artikel behandelt ausschließlich Trommelbremsen. Für Vorschläge zu besseren oder schlechteren Bremsen für unterschiedliche Arten von Fahrrädern (Kinder, Alltag, Reise, Tandems, Mountainbikes, Rennräder, usw.) sollte man mit dem Übersichtsartikel Die richtige Bremse für mein Fahrrad beginnen. Weitere interessante Artikel sind die Bemerkungen zu Bremshebeln von Direktzugbremsen und der Artikel über Bremszüge.

Eine Sturmey-Archer Trommelbremse

Was ist eine Trommelbremse?

Eine Trommelbremse ist eine mit der Hand angesteuerte Nabenbremse, bei denen die Bremsbeläge von Innen gegen eine zylindrische Trommel drücken.. Trommelbremsen waren eine zeit lang die am weitest verbreiteten Bremsentypen für Motorfahrzeuge und wurden inzwischen von Scheibenbremsen abgelöst. Trommelbremsen sind bei Lastenrädern in Ländern mit feuchtem Wetter sehr beliebt. Weniger beliebt sind sie bei Alltags- oder Rennrädern, bei denen Felgenbremsen vorherrschen und Scheibenbremsen auf dem Vormarsch sind.

Eine Trommelbremse kann sowohl ein integraler Bestandteil der nabe sein oder si wird an der linken Seite der nabe ähnouch wie ein Schraubkranz (rechts) aufgeschraubt. Da das Drehmoment der Bremse gegenläufig zu dem eines Schraubkranzes ist, ist das Gewinde genauso ein Rechtsgewinde wie das beim Schraubkranz.

Eine vordere Trommelbremse lässt sich mit einem Nabendynamo verbinden so wie sich eine Hintere Trommelbremse mit einer Nabenschaltung verbinden lässt. Spezielle sehr große Trommelbremsenmodelle wurden als Schleppbremsen für Tandems benutzt, da sie gute Hitzeleitfähikeiten bei langen Abfahrten bieten.

Die Shimano Rollerbrake ist eine spezielle Art der Trommelbremse und wird in einem separaten Artikel behandelt.

Wie funktioniert eine Trommelbremse?

Eine Trommelbremse hat zwei Bremsbläge, die sich gegenüberliegen. Sie werden durch einen Mechanismus aktiviert, der sie auf einer oder auf beiden Seiten aueinanderdrückt. Dieser Auswärtsdruck gegen die Innenseite der Trommel erzeugt Reibung. Die Trommel ist Teil des Nabenkörpers oder wird an die Nabe angeschraubt und verlangsamt durch die Reibung das Laufrad. Die Bremsbeläge sind auf einem Bremsträger montiert, der mit der Achse und durch eine Drehmomentstütze mit dem Rahmen oder der Gabel verbunden ist, um Drehmoment aufzunehmen. Wenn man die Bremse löslässt, holt eine Feder die Bremsbeläge wieder einwärts weg von der Bremstrommel.

Most automotive drum brakes are operated by hydraulic pistons, but bicycle drum brakes use a cable with a linkage to a cam that pushes the brake shoes outward. The photo below shows a Sturmey-Archer drum brake partially disassembled. The hub shell with the drum is at the top and the brake shoes on their backing plate are at the bottom.

The photo below highlights the location of a pivot (blue arrow) which has a snap ring allowing removal and replacement of the brake shoes. A spring is hidden under the brake shoes, except for its ends, highlighted by the green arrows. The spring retracts the brake shoes when the brake is released.

Location of pivot and spring

The next picture shows how a lever rotates the cam (red arrow) and spreads the brake shoes. When the brake is in use, the cable housing attaches at the C-shaped fitting which my thumb is holding, and the inner wire of the cable is clamped to the end of the lever. The hole at the end of the reaction arm is for a clamp band that secures the reaction arm to the frame or fork.

The shape of the cam affects the operation of the brake. As the elongated cam of this brake (typical of bicycle drum brakes) turns to apply the brake harder, the mechanical advantage increases. The hand lever must be pulled farther, and the force therefore does not increase as quickly as might be expected. Also as the brake shoes wear, the mechanical advantage increases. A cam with a spiral-shaped surface on each side would result in a linear relationship, more like that of other brakes, but also increased friction, so the cam might not retract the shoes, cable or hand lever.

Operation of drum brake

Bicycle brakes use a simplex mechanism for the sake of mechanical simplicity. One end of each brake shoe is attached to a pivot, hardly moves outward, and wears little. The leading shoe is the one where the brake drum is rotating toward the pivot; vice versa for the trailing shoe. The rotation of the drum tends to make the leading shoe "dig in," pressing harder against the drum, and removing some load from the cam, while the corresponding effect on the trailing shoe tends to reduce its load on the pivot and put additional load on the cam. At first, the leading shoe wears faster, but the cam produces equal displacement of both shoes (give or take the small difference in radius at which the cam acts). For this reason, the force on the two shoes, and the wear, equalize themselves once the brake has worn in.

Which shoe is the leading one depends on whether the wheel is rolling forward or backward. A bicycle brake is used mostly when rolling forward, though also to prevent the bicycle from rolling backward when stopped facing uphill.

The illustration below represents cam actuation as well as two types of hydraulic actuation, which produces equal force rather than equal displacement at the brake shoes. The duplex type has, in effect, two leading shoes. The duplex type, unlike the simplex, is much less effective when the vehicle is traveling backward than when it is traveling forward. Can you see why?

Drum brake types. The black crescents outside the drum are graphs of the pressure of the brake shoes against the drum. Illustration CC by SA 4.0 by Wikipedia contributor A7N8X, modified.

Drum brake types

Nabenbremse vs. Felgenbremse

Vorteile der Nabenbremse

Hub brakes don't have to arch over the tire, and so no design compromises are needed with wide tires.
Hub brakes are little affected by wet conditions.
They don't get clogged with mud and snow.
They don't wear rims -- especially an issue in sand and mud, or with carbon-fiber composite rims.
They aren't affected by rim damage or out-of-true.
They don't risk brake shoes' damaging the tire or diving under the rim and locking the wheel.
They don't leave black dust (wear particles) on aluminum-alloy rims, to get all over your hands when you remove or replace a wheel.
They work especially well with small wheels.
They dissipate heat without overheating the tire -- of special importance when used as a downhill drag brake on a tandem or cargo bike. (Few drum brakes, though, are designed for this use.)
They allow modifications which don't work with rim brakes, for example, reflective tape on the sides of the rim; zip ties as tire chains wrapped around the rim and tire.
Some frames have no provision to mount rim brakes, and so hub brakes are the only option

Nachteile der Nabenbremse

A hub brake can get much hotter than a rim with a rim brake, risking injury if touched, and damage to nearby fabric or plastic items.
Heat buildup in drum brakes that are integral with the hub can vaporize the lubricant in the hub (as with coaster brakes).
The effectiveness of a hub brake depends on the diameter of the drum or disc. A small-diameter brake is generally weaker and has poorer heat dissipation.
The torque from heavy use of a front hub brake results in "brake steer" unless the front fork is especially stiff, and can bend a fork blade unless it is especially strong.
Hub brakes are generally heavier than rim brakes.

Trommelbremse vs. Scheibenbremse

Vorteile der Trommelbremse

Drum brakes require less frequent maintenance than disc brakes.
A drum brake has no external rotor which risks getting warped or bent, and whose sharp edges can cause injury in a crash.
A front drum brake does not tend to pull the wheel out of the fork.
Drum brakes are generally easier to modulate than disc brakes.

Nachteile der Trommelbremse

Most bicycle drum brakes are an integral part of the hub. If the drum is worn out, the hub, and so, generally, the wheel, must be replaced. A disc-brake rotor is easily replaced.
A front drum brake is less likely than a disc brake to be effective enough for a quick stop.
A drum brake can sometimes "stick" and not release when the bicycle stops, due to self-energizing of the leading shoe. Rolling slightly backward releases the brake.
The lubricant can contaminate the brake shoes of a drum brake if the wheel bearing is inboard of the brake drum. This is more common if the brake gets hot, and with oil lubrication. This can contribute to the brake's "sticking" .
A wheel bearing inboard of the brake drum (with most drum brakes) also makes the axle more prone to bending and breakage.
Most drum brakes have poor heat dissipation, making them prone to brake fade, and so are not suitable for speed control on long downhill runs.
A drum brake makes the wheel harder to remove and replace. Most drum brakes do not allow a quick-release axle. The reaction arm and cable must be disconnected and reconnected. Some drum brakes do have quick-release attachments for these. A disc brake usually requires only adjustment of caliper clearance after replacing the wheel.
Disc brake calipers and rotors are easily interchanged. Drum-brake shoe assemblies are proprietary.
Most drum brakes have the spoke holes at the outside of the drum, and the large spoking diameter requires special attention when building a wheel, in particular, a low cross number if a small-diameter rim is used.

All in all, the better drum brakes can be a good choice on bicycles which are ridden in flatlands and wet weather -- typically, urban conditions, and more so on the rear wheel than the front.

Sicherheitsaspekte der Trommelbremse

One-sided mounting results in an unbalanced load on the front fork, potentially leading to handling issues. The load on the fork is heavy because the reaction arm takes up the torque from braking at a relatively short distance from the hub. However, a drum brake does not tend to pull the front hub out of the fork like a disc brake, because the backing plate and drum are both connected to the axle, Forces from the brake shoes and drum are equal and opposite at the axle and cancel each other out, so the reaction arm resists only torque. As mentioned, with a strong front drum brake, though, the torque may be enough to flex the fork, causing "brake steer" or even bending a fork blade.

It goes without saying that the cable to any front hub brake on a suspension fork must be run in housing, but the cable to a front hub brake with a rigid fork must also be run in housing, because flexing of the fork during braking can tighten an open cable and lock the brake.

Someone didn't read our advice on cable routing. DO NOT RUN AN OPEN CABLE TO A FRONT HUB BRAKE! The rear cable is a bit long too, but that isn't a killer.

Open drum-brake cable. Do not do this!

Older brake-shoe linings generally contain asbestos, which causes lung cancer. Avoid breathing the dust from these linings.

And, as mentioned, typical drum brakes do not dissipate heat well enough to avoid brake fade or vaporizing the grease in the hub bearings, if used for speed control on long downhills.

Montage und Wartung

A drum brake that is integral with the hub must of course be built into a wheel. The spokes must be crossed on the brake side of the hub to withstand the torque from the hub. A low cross number may be needed to avoid an excessive rim entry angle with a large-diameter of the drum and small wheel.

Most drum brakes use the same brake levers as caliper brakes. Some may work better with longer-travel levers, but also note the pulley trick described below.

The cable, as already mentioned, must run in housing to a front drum brake, but an open cable may run to a rear drum brake.

Apply the brake when tightening down the locknut that secures the brake-shoe backing plate. If an open cable runs to the brake, you will need to use another cable (in housing) for this step, as the left axle nut must still be loose. This step centers the brake shoes so they contact the drum evenly and equally.

Tighten the axle nuts and reaction arm in steps, so they don't cause each other to bind before reaching their final positions. The reaction arm must be securely bolted to a part of the fork or frame capable of resisting the torque. Attachment should be with a clip that cinches tightly and prevents the reaction arm from rotating even a little bit if the brake is applied when the bicycle is facing uphill or rolling backward. Repeated back-and-forth motion of the reaction arm will loosen the axle nuts. Some bicycles have a "Pac Man" fitting on the left chainstay, so the reaction arm can simply be slid into and out of position; and also, there may be a quick release for the cable.

Cable quick release for a drum brake

cable quick release for a drum brake

In the photo below, an old Sturmey-Archer steel pulley doubles the cable travel and mechanical advantage with an (also old) Atom drum brake and serves as a cable quick release. The same trick is possible with the larger pulley of a Problem Solvers Travel Agent, avoiding the use of its smaller pulley, which would more quickly cause metal fatigue to the cable.

Pulley as cable-travel doubler and quick release

Pulley as cable QR

A drum-brake hub requires the same bearing maintenance as other hubs, and occasional cable adjustment as the brake shoes wear. If cable adjustment does not restore brake performance, the brake should be disassembled to check the shoes for wear and contamination. Often, the problem is that they have glazed, and a light sanding will cure the problem, but beware of asbestos with older brake linings.

Werbung:

Siehe auch

Die richtige Bremse für mein Fahrrad
Bemerkungen zu Bremshebeln von Direktzugbremsen
Züge
Das 1x1 der Shimano Rollerbrake
Wikipedia on drum brakes
Wikipedia on bicycle drum brakes
Bike-manual.com on drum brakes
Precision Tandems page about the Arai drag brake for tandems
Technical paper about cam-operated simplex drum brakes

Quelle

Dieser Artikel basiert auf dem Artikel Bicycle Drum Brakes von der Website Sheldon Browns. Originalautor des Artikels ist John Allen.

Weitere interessante Artikel zum Thema Nabenbremse

Weitere interessante Artikel zum Thema Sheldon Brown